Translate Page in your Language

Componenets to build a drone

Necessary componenets to build a drone

To make a drone you need the following componenets

The frame work
Propellers
ELECTRONIC SPEED CONTROLLERS
DRONE MOTORS
THE ELECTRONIC SPEED CONTROLLERS
Power Distribution
Batteries
Battery Monitor
THE LANDING GEAR
FLIGHT CONTROLLE SYSTEM
WIRELESS REMOTE CONTROL SYSTEM
THE FLIGHT CONTROLLER
THE CONTROL PANEL
CAMERA TO YOUR DRONE

The frame work

No matter what your RC quadcopte drone is going to be, it must have a frame. So the first task is to get the framework to work.
When it comes to drone frame, there are two options. You can do it yourself or buy it in the online store, with a wide selection of high-quality frames. If you decide to build it yourself, the project is not that difficult, but you will need some engineering knowledge and knowledge of the materials that you intend to use.

Propellers

When looking for propellers, you should find the ones that fit your drone frame. you have to make sure the ones you choose are appropriate.

ELECTRONIC SPEED CONTROLLERS

Electronic speed controllers, propellers and engines are some of the most important elements of a functional RC quadcopter. Therefore, you should purchase these components from an authorized dealer. They need to fit the size of your drone, so keep that in mind when buying.

DRONE MOTORS

The next thing you need to do is drill the holes in the engine frame according to the distance between the screw holes on the engines. It would be good to make another hole that would allow the clamp and the motor shaft to move freely.
However, you can skip this action if the engines are already equipped with supports. Place the motor in a suitable location and secure it to the frame with screws and a screwdriver.
For a normal ATV, you only need 4 engines, but an octocopter needs eight engines to fly. It is recommended to use brushless motors - they are easier to use up the battery, and if you are not an engineer who fully understands how the motor works, you should buy these parts in the store.

MOUNT THE ELECTRONIC SPEED CONTROLLERS

After installing the motors, the speed controls must also be installed. How do you do that? It is recommended to connect the speed controls on the underside of the frame for several reasons. < bR/> ESC or electronic speed control: these are also important parts of your drone, as they are responsible for powering the engines. Again, their number depends on the number of weapons that your drone will have.

Power Distribution

The power distribution board connects the electronic speed controllers to the battery. The power distribution board allows our battery to power the equipment in a simple and clean way, instead of having power cable sockets laid between the components.

Batteries

When purchasing batteries for a drone, you must take into account the battery capacity and its type. Most often, lithium-lithium batteries are used for this purpose, and their power is different.

Battery Monitor

It's not a rudimentary item, but the monitor is very useful for alerting you when the batteries are about to run out. Thus, you do not risk that the throne will remain without juice in the air above the reservoir.
The assembly location reduces vibration and therefore improves flight. This is very useful, especially if you are trying to take photos or take videos with a drone.

THE LANDING GEAR

The landing gear is an important part when landing your UAV, because it significantly reduces the impact when the drone lands on solid ground. This can be done in different ways, but you need to be creative and do it in your own way and in a unique way.

FLIGHT CONTROLLE SYSTEM

Every flying drone must have a flight control system. This electronic system allows the drone to stay in the air during the flight and cope with all shifts and changes in direction and wind.
The device controller distributes power and simultaneously controls the motors.

WIRELESS REMOTE CONTROL SYSTEM

This wireless remote control system is necessary to control the drone.
Various wireless control systems are currently available. Of course, if you have a transmitter, you also have a receiver mounted on the drone.

MOUNT THE FLIGHT CONTROLLER

Once you have selected a specific flight controller, you need to install it. For example, you can place it on top of the frame in a certain direction, but you need to make sure that all the components are fixed before calibrating your drone. You can also use the above-mentioned ties for this.
It is recommended to put a small piece of sponge on the bottom of the flight controller, as it absorbs and reduces the vibration of the engines. This way, your drone will be more stable in flight.

CONNECT DRONE TO THE CONTROL PANEL

The next thing you need to do is set up and connect the flight controller to the electronic speed controllers. You also need to connect the drone to the control panel.

CONNECT CAMERA TO YOUR DRONE

If you want to take aerial photos and record the situation during the flight of your drone, you will need a camera. The best cameras are those that can shoot high-quality video, but everyone will find it according to their needs. For high-quality photos and videos you will also need a cardan for the camera. USB key is needed to save photos and videos

TEST YOUR DRONE

Before you can finally use the drone, you need to make sure everything is working fine. Therefore, before the first flight, you need to check all the functions. You can test the sensors as well as other components of your drone.
To make sure that everything works well, you need to remove the props and conduct a small experiment with the remote control. This ensures that you can test the drone without risking breaking it.

TAKING OFF

This is the most important step. Before takeoff, the battery must be securely connected and all components must be locked in place. For a test flight, you need to carefully choose the location, as this aircraft can cause serious damage.
Put the ATV on the ground, turn it on, take the flight controller and start your first flight. It is recommended to slowly gas the drone and fly at low altitude for the first time

How to build a drone

No comments:

Post a Comment